wip lab4, tested module

HDL/sdmod.sv

@@ -0,0 +1,23 @@
+module sdmod (
+	input signed [7:0] val,
+	input clk,
+	input reset,
+	output daco
+);
+
+logic out;
+logic signed [7:0] eps;
+logic signed [7:0] un;
+
+always_ff @(posedge clk, negedge reset) begin
+	if (~reset) begin
+		un <= 8'd0;
+	end else begin		
+		un <= val - eps;
+	end
+end
+
+assign daco = (un >= $signed(8'd0)) ? 1'd1                 : 1'd0;
+assign eps  = (un >= $signed(8'd0)) ? $signed(8'd126) - un : $signed(-8'd126) - un;
+
+endmodule

HDL/sigdel.sv

@@ -11,11 +11,27 @@ module sigdel
 	output logic fout
 );
 
+	logic [7:0] phinc_val, phase, sine;
+	
+	//control slave logic
+	always_ff @ (posedge clk or negedge clr_n) begin
+		if (!clr_n) begin
+			phinc_val[7:0] <= 8'd0;
+		end else	begin
+			if (!wr_n) begin
+				phinc_val[7:0] <= wr_data[31:0];
+			end
+		end
+	end
+
 	phacc phacc_inst (.phinc(phinc_val), .clk(clk), .reset(clr_n), .phase(phase));
 	defparam phacc_inst.WIDTH = PHACC_WIDTH;
 	
-	sinelut	sinelut_inst (
+	sinelut sinelut_inst (
        .address (phase), .clock (clk), .q(sine)
 	);
-
+	
+	sdmod sdmod_inst (
+	    .val(sine), .clk(clk), .reset(clr_n), .daco(fout)
+	);
 endmodule

Testbench/sigdel/lut_mod_tb.sv

@@ -0,0 +1,55 @@
+`timescale 1 ns/1 ns
+
+module lut_mod_tb();
+
+	// Parameters
+	localparam CLK_PRD = 20;
+	localparam PHACC_WIDTH = 14;
+	
+	logic clk, clr_n, wr_n, daco;
+	logic [7:0] phinc_val, phase, sine;
+		
+	// Instantiate UUT and connect used ports
+	phacc phacc (
+	    .phinc(phinc_val), .clk(clk), .reset(clr_n), .phase(phase)
+	);
+	defparam phacc.WIDTH = PHACC_WIDTH;
+	
+	sinelut sinelut_inst (
+       .address(phase), .clock(clk), .q(sine)
+	);
+	
+	sdmod sdmod_inst (
+	    .val(sine), .clk(clk), .reset(clr_n), .daco(daco)
+//	    .val(8'd0), .clk(clk), .reset(clr_n), .daco(daco)
+//	    .val(8'd255), .clk(clk), .reset(clr_n), .daco(daco)
+	);
+
+
+	// Clock definition
+	initial begin
+		clk = 0;
+		forever #(CLK_PRD/2) clk = ~clk;
+	end
+
+	// Reset and initial values definition
+	initial begin
+		clr_n = 0;
+		#(CLK_PRD*5) clr_n = 1;
+	end
+	
+	// Bus write transaction simulation
+	initial begin
+		// Wait until system is out of reset
+		@(posedge clr_n);
+		
+		phinc_val=(2**(PHACC_WIDTH - 8));
+		if ((phinc_val <= 255) && (phinc_val != 0)) begin
+          #(CLK_PRD * 256 * 10) $stop;
+		end else begin
+			$display("Error: value of phase increment is out of range! Stopped simulation.");
+			#1 $stop;
+		end
+	end
+endmodule
+

Testbench/sigdel/sigdel.qsf

@@ -50,19 +50,28 @@ set_global_assignment -name NOMINAL_CORE_SUPPLY_VOLTAGE 1.2V
 set_global_assignment -name EDA_SIMULATION_TOOL "ModelSim-Altera (SystemVerilog)"
 set_global_assignment -name EDA_TIME_SCALE "1 ps" -section_id eda_simulation
 set_global_assignment -name EDA_OUTPUT_DATA_FORMAT "SYSTEMVERILOG HDL" -section_id eda_simulation
-set_global_assignment -name SYSTEMVERILOG_FILE ../../HDL/phacc.sv
 set_global_assignment -name POWER_PRESET_COOLING_SOLUTION "23 MM HEAT SINK WITH 200 LFPM AIRFLOW"
 set_global_assignment -name POWER_BOARD_THERMAL_MODEL "NONE (CONSERVATIVE)"
-set_global_assignment -name QIP_FILE ../../HDL/IP/sinelut.qip
-set_global_assignment -name SYSTEMVERILOG_FILE ../../HDL/sigdel.sv
-set_global_assignment -name SYSTEMVERILOG_FILE inc_lut_tb.sv
 set_global_assignment -name PARTITION_NETLIST_TYPE SOURCE -section_id Top
 set_global_assignment -name PARTITION_FITTER_PRESERVATION_LEVEL PLACEMENT_AND_ROUTING -section_id Top
 set_global_assignment -name PARTITION_COLOR 16764057 -section_id Top
 set_global_assignment -name EDA_TEST_BENCH_ENABLE_STATUS TEST_BENCH_MODE -section_id eda_simulation
-set_global_assignment -name EDA_NATIVELINK_SIMULATION_TEST_BENCH inc_lut_tb -section_id eda_simulation
+set_global_assignment -name EDA_NATIVELINK_SIMULATION_TEST_BENCH sigdel_tb -section_id eda_simulation
 set_global_assignment -name EDA_TEST_BENCH_NAME inc_lut_tb -section_id eda_simulation
 set_global_assignment -name EDA_DESIGN_INSTANCE_NAME NA -section_id inc_lut_tb
 set_global_assignment -name EDA_TEST_BENCH_MODULE_NAME inc_lut_tb -section_id inc_lut_tb
+set_global_assignment -name EDA_TEST_BENCH_NAME lut_mod_tb -section_id eda_simulation
+set_global_assignment -name EDA_DESIGN_INSTANCE_NAME NA -section_id lut_mod_tb
+set_global_assignment -name EDA_TEST_BENCH_MODULE_NAME lut_mod_tb -section_id lut_mod_tb
+set_global_assignment -name SYSTEMVERILOG_FILE ../../HDL/phacc.sv
+set_global_assignment -name QIP_FILE ../../HDL/IP/sinelut.qip
+set_global_assignment -name SYSTEMVERILOG_FILE ../../HDL/sigdel.sv
+set_global_assignment -name SYSTEMVERILOG_FILE ../../HDL/sdmod.sv
+set_global_assignment -name EDA_NATIVELINK_SIMULATION_SETUP_SCRIPT simulation/modelsim/wave.do -section_id eda_simulation
 set_global_assignment -name EDA_TEST_BENCH_FILE inc_lut_tb.sv -section_id inc_lut_tb
+set_global_assignment -name EDA_TEST_BENCH_FILE lut_mod_tb.sv -section_id lut_mod_tb
+set_global_assignment -name EDA_TEST_BENCH_NAME sigdel_tb -section_id eda_simulation
+set_global_assignment -name EDA_DESIGN_INSTANCE_NAME NA -section_id sigdel_tb
+set_global_assignment -name EDA_TEST_BENCH_MODULE_NAME sigdel_tb -section_id sigdel_tb
+set_global_assignment -name EDA_TEST_BENCH_FILE sigdel_tb.sv -section_id sigdel_tb
 set_instance_assignment -name PARTITION_HIERARCHY root_partition -to | -section_id Top

Testbench/sigdel/sigdel.sv

@@ -0,0 +1,37 @@
+//top-level module
+module sigdel
+#(
+    PHACC_WIDTH = 14
+) (
+	//clock and reset
+	input logic clk, clr_n,
+	//control slave
+	input logic [31:0] wr_data,
+	input logic wr_n,
+	output logic fout
+);
+
+	logic [7:0] phinc_val;
+	
+	//control slave logic
+	always_ff @ (posedge clk or negedge clr_n) begin
+		if (!clr_n) begin
+			phinc_val[7:0] <= 8'd0;
+		end else	begin
+			if (!wr_n) begin
+				phinc_val[7:0] <= wr_data[31:0];
+			end
+		end
+	end
+
+	phacc phacc_inst (.phinc(phinc_val), .clk(clk), .reset(clr_n), .phase(phase));
+	defparam phacc_inst.WIDTH = PHACC_WIDTH;
+	
+	sinelut sinelut_inst (
+       .address (phase), .clock (clk), .q(sine)
+	);
+	
+	sdmod sdmod_inst (
+	    .val(sine), .clk(clk), .reset(clr_n), .daco(fout)
+	);
+endmodule

Testbench/sigdel/sigdel_tb.sv

@@ -0,0 +1,81 @@
+`timescale 1 ns/1 ns
+
+module sigdel_tb();
+
+	// Parameters
+	localparam CLK_PRD = 20;
+	localparam SAMPLES_PRD = 256;
+	localparam OVERSAMPLING = 4;
+	localparam PHACC_WIDTH = 14;
+	
+	// Wires and variables to connect to UUT (unit under test)
+	logic clk, clr_n, wr_n;
+	logic [31:0] wr_data;
+	logic [31:0] phinc_val;
+	logic fout;
+		
+	// Instantiate UUT and connect used ports
+	sigdel dut(.clk(clk), .clr_n(clr_n), .wr_n(wr_n), .wr_data(wr_data), .fout(fout));
+	defparam dut.PHACC_WIDTH = PHACC_WIDTH;
+
+	// Clock definition
+	initial begin
+		clk = 0;
+		forever #(CLK_PRD/2) clk = ~clk;
+	end
+
+	// Reset and initial values definition
+	initial begin
+		clr_n = 0;
+		wr_n = 1;
+		wr_data = 'bx;
+		#(CLK_PRD*5) clr_n = 1;
+	end
+	
+	// Bus write transaction simulation
+	initial begin
+		// Wait until system is out of reset
+		@(posedge clr_n);
+		// Check if phase increment for required accumulator width 
+		// and oversamlpling ratio will fit in 8 bits
+		phinc_val=(2**(PHACC_WIDTH-8))/OVERSAMPLING;
+		if ((phinc_val <= 255) && (phinc_val != 0))
+		begin
+			// Write phase increment several clock cycles after reset
+			#(CLK_PRD*3) write_transaction(phinc_val);
+			// Wait for one sine period (for 14-bit phase accumulator case)
+			#(CLK_PRD*SAMPLES_PRD*OVERSAMPLING)
+
+			#(CLK_PRD*3) write_transaction(phinc_val*5);
+
+			#(CLK_PRD*SAMPLES_PRD*OVERSAMPLING)
+			$stop;
+		end
+		else
+		begin
+			//Output simulation error
+			$display("Error: value of phase increment is out of range! Stopped simulation.");
+			//Stop simulation (small delay needed for $display to work)
+			#1 $stop;
+		end
+	end
+
+	//Single write transaction task
+	task write_transaction;
+		//input signals
+		input [31:0] val;
+		//transaction implementation
+		begin
+			@(posedge clk);
+			//assert signals for one clock cycle
+			wr_n = 0;
+			wr_data = val;
+			@(posedge clk);
+			//deassert signals
+			wr_n = 1;
+			wr_data = 'bx;
+		end
+	endtask
+
+endmodule
+